INFO SEWA

CALL: 081287399003(call/SMS/WA)

SEWA HT TERLENGKAP SETTING MENU HT BAOFENG UV82

SEWA HT TERLENGKAP CALL 081287399003

Setting Menu pada HT Baofeng UV82


Pada postingan kali ini admin masih berkutat pada pembahasan mengenai HT Baofeng UV-82..
Memang tidak dipungkiri kehandalan HT ini sangat baik, dengan berbagai fitur yang terdapat di “menu



Setting di Menu pada HT Baofeng UV-82..

" 0 "   SQL Squelch Level 
         (Squelch silences the receiver when there is no signal) 0 > 9
  • UHF Sensitivity can be varied from .1 to .3 mV 
  • VHF Sensitivity is constant. 1 > 9 = .1 mV 
  • Level 0 = Open Squelch
  • There is little difference between settings. 
  • Level 5 is recommended. 
1 " STEP Frequency Step
(Amount of frequency change 2.5 / 5 / 6.25 / 10 /12.5 / 25 / 50 kHz)

" 2 "  TXP Transmit Power
  • UV82 - High = 5W  Low = 1W 
  • 82HP - High = 8W  Mid = 4W  Low = 1W
  • Use Low power unless necessary. 
  • Power can be toggled Hi/Lo by pressing the [ #   ] key.
" 3 "  SAVE Battery Save
  • Sleep Ratio to acknowledge an RX signal.
  • The higher number increases the RX sleep cycle, 1=1:1    2=1:2    3=1:3    4=1:4
" 4 "  VOX Voice Operated Xmtr
  • Allows transmitter activation by talking only.
  • Adjust VOX gain to allow smooth operation.
  • Level  10  requires the strongest voice.
5 " WN Wideband / Narrowband
  • Wide = 5 KHz    Narrow = 2.5 KHz
  • For Ham use, start with selecting Wide. 
" 6 "   ABR Display Illumination Time
  • Time the display stays illuminated.
" 7 " TDR Dual Watch / Dual Reception
  • Allows monitoring of 2 channels, toggling between Freq A and Freq B.
  • If a signal is received, the RX remains on that channel until the signal is gone.
 " 8 " BEEP Keypad Beep
  • Allows audible confirmation of a key press
" 9 "    TOT Transmission  Time Out Timer
  • Transmit Times Out after pre-selected time.
  • Radio will alert you when the time is up.
  • This helps prevent overheating.
" 10 " R-DCS Rec - Digital Coded Squelch
  • Prevents interference from signals on the same frequency.
  • The squelch will open only if the incoming signal is coded with the same tone required
  • Note: Not all repeaters requiring a tone for access transmit a tone back to you. 
  • Leave this function turned OFF unless you are absolutely sure it is needed.
" 11 " R-CTCS Rec - Continuous Tone Coded Squelch
  • Prevents interference from signals on the same frequency.
  • The squelch will open only if the incoming signal is coded with the same tone required
  • Leave this function turned OFF unless you are absolutely sure it is needed.
  • Note: "Not all repeaters requiring a tone for access transmit a tone back to you".
" 12 "  T-DCS Trans - Digital Coded Squelch
  • Required by some networks to limit access and interference
" 13 "  T-CTCS Trans - Continuous Tone Coded Squelch
  • Required by some networks to limit access and interference
" 14 "   VOICE   Voice Prompt
  • Audible confirmation of a keypad entry
" 15 "   ANI-ID   Automatic Number ID of Radio (set with S/W)
  • Sent when PTT is pressed and/or released.
  • Used to alert dispatcher which field radio was keyed.
  • Used primarily for commercial applications.
" 16 "  DTMFST DTMF Tone of transmit
  • Determines when DTMF codes are heard through speaker.
  • OFF       No tones heard
  • DT-ST    Only manually keyed DTMF codes are heard
  • ANI-ST   Only automatically keyed DTMF codes are heard
  • DT+ANI   * All DTMF codes are heard
" 17 "  S-CODE   Signal Code
  • PTT-ID DTMF Code Selection    (set with S/W)
  • Selects one of 15 DTMF codes.
  • Set with software and are up to 5 digits each.
  • Enabled by using Menu 19.
" 18 "  SC-REV    Scan Resume Method
     - TO (Time Operation) Scan stops when signal detected.
             Scan resumes after after predetermined time.
     - CO (Carrier Operation) Scan stops when signal detected.
             Scan resumes when signal disappears.
     - SE (Search Operation) Scan stops when signal detected.
             Scanning will not resume.

" 19 "   PTT-ID     When to send the PTT ID signal code
  • OFF -   No ID is sent.
  • BOT -   An ID is sent at Beginning of Transmission
  • END -   An ID is sent at the End of Transmission.
  • BOTH - An ID is sent at BOT and EOT
  • This tells a dispatcher which field radio was keyed.
  • Not Applicable for Ham use.   Set to OFF.
" 20 "   PTT-LT    Signal Code sending delay
               Not Applicable for Ham use.   Set to 0 (zero)

" 21 "   MDF-A    Channel Mode A Display   (upper display)
  • FREQ - Displays programmed Frequency
  • CHAN - Displays Channel Number
  • NAME - Displays Channel Name programmed via software
" 22 "   MDF-B    Channel Mode B Display   (lower display)
  • FREQ - Displays programmed Frequency
  • CHAN - Displays Channel Number
  • NAME - Displays Channel Name programmed via software
" 23 "   BCL     Busy Channel Lockout

  • Prevents transmitting on a busy frequency.
  • If another repeater or signal is present using a different CTCSS or DCS code, 
  • your transmitter will be 'locked out' to prevent interference.  
  • When PTT is keyed, radio will sound a Beep Tone.
" 24 "  AUTOLK Automatic Keypad Lock

  • When ON, keypad will be locked if not used in 8 seconds.
  • Pressing the  [#  ]  key for 2 seconds will Lock/Unlock the keys on the keypad.
" 25 "  SFT-D      Frequency shift direction
  • Enables access of repeaters in VFO/FREQ mode.
  • OFF          TX = RX (simplex)
  • + (plus)     TX shifted Higher in freq than RX
  • -  (minus)  TX shifted Lower in freq than RX
" 26 "   OFFSET  Frequency shift amount
  • Specifies frequency difference between TX and RX.
  • Used with Menu 25 for repeater access in VFO/FREQ mode.
  • Offset is not required when storing repeater frequencies into channels.
" 27 "   MEM-CH    Store a memory channel
  • Stores channel information in memory slot  0 > 127
  • For a detailed examples of the programming process, 
  • please visit:      Programming Memories
  " 28 "  DEL-CH Delete a memory channel
  • Deletes  information stored in memory slot  0 > 127
 " 29 "  WT-LED Illumination / Display Color - Standby
  • Screen illumination color in Standby Mode
" 30 "   RX-LED Illumination / Display Color - Receive
  • Screen illumination color in Receive Mode
" 31 "  TX-LED Illumination / Display Color - Transmit
  • Screen illumination color in Transmit Mode
" 32  " AL-MOD Alarm Mode
  •  SITE - Sounds alarm through your radio speaker only.
  •  TONE - Transmits a cycling tone over the air.
  •  CODE - Transmits '119' followed by ANI code over the air.
" 33 "   BAND       Band Selection
  • In VFO/FREQ mode, sets VFO A or B to VHF or UHF band.
" 34 "  TDR-AB   Transmit selection while in Dual Watch / Dual Reception
  • This option has no effect on a UV-82. 
  • It is overridden by the dual PTT button.
  • Note: a single button Spkr-Mic will select channel B
" 35  "  STE       Squelch Tail Elimination
  • Eliminates the squelch tail at the end of a transmission. 
  • Only works when other radios turn on their Tail function.
  • For Ham use, set to OFF.
" 36 "   RP-STE  Repeater Squelch Tail  Elimination
  • Requires a repeater using this function.
  • For Ham use, set to OFF.
" 37 "   RPT-RL  Delay the squelch tail of repeater
  • For Ham use, set to OFF.
" 38 "   PONMSG Boot / Power On Display
  • FULL - Displays the entire LCD screen.
  • MGS - Displays a 2 line Power On message.
" 39 "   ROGER Tone at end of transmission
  • Sends a Tone at the end of each transmission.
  • For Ham use, set to OFF.

Demikian menu setting di HT Baofeng UV 82 dipersembahkan untuk agan-agan yang mau setting HT Baofengnya..
Silahkan di Share tolong tetap mencantumkan link http://www.fixlinkcommunication.com ya gan..
Fixlink Communication Tempat Sewa HT Terlengkap...









Share this article :
+
Previous
Next Post »
1 Komentar untuk "SEWA HT TERLENGKAP SETTING MENU HT BAOFENG UV82"